Search:

Type: Posts; User: Polish_Eagle

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    1,005

    Re: Mazda 3 2.0 Radiator Replacement Time

    Oh boy, don't know what I was thinking when I wrote my above comment, it must have been a rough morning.. lol

    Flagrum_3 is definitely correct about using coolant. Just to add to this, you still...
  2. Replies
    6
    Views
    1,005

    Re: Mazda 3 2.0 Radiator Replacement Time

    If temperatures never reach freezing you can use just distilled water. However, if temperatures do reach freezing, you absolutely need some antifreeze to prevent damage to the block. You don't have...
  3. Re: would you buy a vehicle with recall (fuel tank) ?

    Why would it matter, it's a recall, and that means the manufacturer fixed said issue. So this is a non-issue. I'd buy it.
  4. Thread: SSL

    by Polish_Eagle
    Replies
    3
    Views
    2,151

    Re: SSL

    I use the following on all my servers (it's free): https://letsencrypt.org/

    Also, to make the install easier there's "certbot" that will install the cert for you and setup HTTPS.
  5. Thread: SSL

    by Polish_Eagle
    Replies
    3
    Views
    2,151

    SSL

    Why doesn't this forum use SSL?
  6. Re: Upgrading Camshafts on MZR L engine (non DISI)

    When replacing cams, you'll also need to do the valve lash adjustment. So worst case scenario, if you had to replace all 16 buckets, you might be adding a lot more in cost. Last I remember when I did...
  7. Re: Sneak Peak into our new exhaust manifold we have coming to a Speed near you!

    Ooooo, do want, would be nice on my build motor with port injection. Moar powa!! :)
  8. Replies
    26
    Views
    8,119

    Re: Zoom Zoom Boom

    Is the suspension stock, if not, what is it and how many KM's on it? Also, do you have an EGR too? PM me pricing for everything.
  9. Re: How to check wiring between key and washer pump/motor switch?

    You'll also need the wire diagrams for your car so you know which wires to look for and test.
  10. Replies
    7,019
    Views
    463,227

    Sticky: Re: Random MS3 Chat Thread

    Mazda VCM2 with their IDS software. I have a high quality clone that I've been using for a while and it definitely is a helpful unit to have.
  11. Replies
    7,019
    Views
    463,227

    Sticky: Re: Random MS3 Chat Thread

    That's a sweet garage setup you have. I always wanted a lift in my garage, I've been on the fence for a quick jack.
  12. Replies
    40
    Views
    8,819

    Re: Pwdunmore's MS6 Logs

    Enjoy, Rob will really bring the car to life! From all my tunes (Rob, Freek, & Stratified) Rob made the most power and also made the car drive the best.
  13. Replies
    40
    Views
    8,819

    Re: Pwdunmore's MS6 Logs

    Spray some soap water on the fittings and create some boost while a friend looks at the fittings. If you see it bubbling there's your problem. You could always go to the hardware store and pickup a...
  14. Replies
    3
    Views
    3,835

    Re: Advice please!

    Absolutely not the same. Do not waste your time and money on attempting it.
  15. Replies
    7,019
    Views
    463,227

    Sticky: Re: Random MS3 Chat Thread

    I have a Gen 2, but the bolt won't come out on the one side if you pull straight out. What I did was unbolt it, and when you try to remove it you need to angle the control arm so the bolt is angled...
  16. Replies
    40
    Views
    8,819

    Re: Pwdunmore's MS6 Logs

    Oh damn, so it's quite impressive your turbo was still hitting 23 PSI. Nice find!
  17. Replies
    7,019
    Views
    463,227

    Sticky: Re: Random MS3 Chat Thread

    Take the wheel off, remove the two control arm bolts, swap arms, now reinstall. That's all I did and the total install time was about 15 minutes a wheel.
  18. Replies
    40
    Views
    8,819

    Re: Pwdunmore's MS6 Logs

    I've had Rob tune my car and he's awesome, so I highly doubt it's tune related. I'd definitely do a smoke test to see if there is a small boost leak. If all is good I'd add more preload and let Rob...
  19. Replies
    40
    Views
    8,819

    Re: Pwdunmore's MS6 Logs

    Is your tune boost, load or hybrid based?
  20. Replies
    2
    Views
    3,586

    Re: Maintenance schedule

    I've put 200k on my OEM timing chain and it was still good. Usually as it wears you'll hear the chain slap against the guard in the valve cover.
  21. Replies
    4
    Views
    3,343

    Re: T6 5w40 vs 0w40

    I've been using the T6 0W40 for quite some time. I haven't noticed any issues with it.
  22. Replies
    8
    Views
    2,769

    Re: Cpe downpipe cobb stage2 tune safe?

    I personally hate the OTS maps, when I use to have an AP I had so many issues with boost cut during the winter. As for tuning, I highly recommend Rob Finkle from Hypnotic Tuning...
  23. Replies
    11
    Views
    2,880

    Re: Rear motor mount

    Until the JBR TMM fails and your transmission drops...
  24. Replies
    11
    Views
    2,880

    Re: Rear motor mount

    That's probably the best decision you can make!
  25. Replies
    11
    Views
    2,880

    Re: Rear motor mount

    I have a Cobb rear mount and it sounds almost as quiet as stock and it also feels pretty solid in the car. I'd recommend avoiding JBR mounts as he has had quite a few fail (documented on MSF and in...
Results 1 to 25 of 303
Page 1 of 13 1 2 3 4