Results 1 to 13 of 13

Thread: Compressing Rear caliper pistons

  1. #1
    Noob Ron_M3 sport's Avatar
    Join Date
    Jul 2008
    Posts
    19
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Compressing Rear caliper pistons

    Help please!

    My rotors were warped and pads were getting low so I purchased some drilled rotors and new pads and thought I'd replace them myself. I found a great step-by-step guide here but I've run into one problem... compressing the rear pistons.
    I've read in a couple online forums that it's as simple as using a pair of needle nose pliers to spin them back in but it's not working for me. I even went out and bought that special cube tool from Cantire but still there not going in far enough. I need another 1/4" clearance. The pistons will turn and you will see them compressing but stop at a certain point. They continue to rotate but it won't compress any further.

    I have the reservoir cap off.
    I'm rotating clockwise.
    I tried with e-brakes on and off.

    Any thoughts?
    2005, 4 spd auto, Titanium Grey, 35% front/ 15% rear tint, 17" Falken FK452, cross-drilled rotors, Ractive Short Ram Intake, Koni FSD Shocks.
    (Soon: Shark Fin Antenna, Mesh front grille)

  2. #2
    Moderator cwp_sedan's Avatar
    Join Date
    Mar 2007
    Location
    GTA
    Age
    41
    Ride
    07 Mazda3 GT Sedan
    Posts
    14,706
    Thanks
    498
    Thanked 256 Times in 151 Posts
    Mentioned
    73 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Compressing Rear caliper pistons

    Maybe this will help, or is this the step-by-step guide you were looking at?

    http://www.torontomazda3.ca/forum/sh...ad.php?t=24152

  3. #3
    Noob Ron_M3 sport's Avatar
    Join Date
    Jul 2008
    Posts
    19
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Compressing Rear caliper pistons

    Quote Originally Posted by cwp_sedan View Post
    Maybe this will help, or is this the step-by-step guide you were looking at?

    http://www.torontomazda3.ca/forum/sh...ad.php?t=24152
    Thanks CWP_Sedan but this was that great post that I mentioned. I've tried everything - I think I might have to bite the bullet and "borrow" that reset tool from Canadian Tire.

  4. #4
    Jr Member Walrus's Avatar
    Join Date
    Feb 2007
    Posts
    480
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Compressing Rear caliper pistons

    Borrow the tool. I couldn't get it in with needle nose and a ton of force.

  5. #5
    Noob Ron_M3 sport's Avatar
    Join Date
    Jul 2008
    Posts
    19
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Compressing Rear caliper pistons

    Ok, so it seems that some 3 do-it-yourselvers can compress the piston with a pliers and a couple pounds of force but this was not the case in my experience!

    When I realized that the "cube" that I purchased earlier today didn't work I actually started to panic a little bit. While I was trying to wind in the piston on the right caliper I unwound it to try to start from the top of the thread and it wouldn't go back down. I thought I screwed it up... I heard that calipers are like $300 per?!

    Anyway, I ended up borrowing the tool from Canadian Tire. "Crappy Tire", as people call it, isn't so bad. They charged $112 to my credit card and if I return it, and do so in good condition they will return the entire amount to my card. How can you beat that?

    Once I took it home and assembled the tool the beads of sweat subsided.

    It was fairly simple to use:

    Choose the connection that fits the dimples on the piston. (In our case the welded on adapter was the best fit)



    Slide on the bracket plate.



    Twist the handle clockwise until the piston is sufficiently compressed to install the new pads.


    Have fun and work safely!

  6. #6
    Noob Ron_M3 sport's Avatar
    Join Date
    Jul 2008
    Posts
    19
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Compressing Rear caliper pistons

    Quote Originally Posted by Ron_M3 sport View Post
    Ok, so it seems that some 3 do-it-yourselvers can compress the piston with a pliers and a couple pounds of force but this was not the case in my experience!

    When I realized that the "cube" that I purchased earlier today didn't work I actually started to panic a little bit. While I was trying to wind in the piston on the right caliper I unwound it to try to start from the top of the thread and it wouldn't go back down. I thought I screwed it up... I heard that calipers are like $300 per?!

    Anyway, I ended up borrowing the tool from Canadian Tire. "Crappy Tire", as people call it, isn't so bad. They charged $112 to my credit card and if I return it, and do so in good condition they will return the entire amount to my card. How can you beat that?

    Once I took it home and assembled the tool the beads of sweat subsided.

    It was fairly simple to use:

    Choose the connection that fits the dimples on the piston. (In our case the welded on adapter was the best fit)

    http://www.torontomazda3.ca/forum/al...&pictureid=136

    Slide on the bracket plate.

    http://www.torontomazda3.ca/forum/al...&pictureid=135

    Twist the handle clockwise until the piston is sufficiently compressed to install the new pads.

    http://www.torontomazda3.ca/forum/al...&pictureid=134

    Have fun and work safely!
    I apologize for the double post... the photo links didn't work.

  7. #7
    Sr Member Wild Weasel's Avatar
    Join Date
    Nov 2006
    Posts
    4,681
    Thanks
    6
    Thanked 16 Times in 8 Posts
    Mentioned
    3 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Compressing Rear caliper pistons

    I can do it with needle nose pliars, but as a couple members here can attest, it involves a lot of angry words and about 20 minutes of seemingly nothing happening before they magically go in.

    That said... I went and bought myself the proper tool (like the one you borrowed) to make my life easier in the future.

    Incidentally... I still install for beer...

  8. #8
    Uncle Ben
    Join Date
    Sep 2005
    Age
    36
    Posts
    4,951
    Thanks
    1
    Thanked 97 Times in 84 Posts
    Mentioned
    40 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Compressing Rear caliper pistons

    heres a tip when compressing the caliper try to keep the brake line as straight as possible so the fluid has no hesitation when travelling through the line hence making it easy for the calipers to compress
    1991 Nissan Pathfinder - trade in, 2005 Mazda 3 GX ty grey - Write off, 2010 Mazda 3 GT E sedan CWP- trade in, 2010 Speed 3 w/tech CWP - Up for sale (soon), 2007 Mazda 3 GS silver- motor swapped in to 2009 MS3 CWP that had blown engine, 2002 BMW 330ci silver- new winter ride, 2005 BMW M3- new toy

  9. #9
    Newbie
    Join Date
    Apr 2005
    Posts
    84
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Compressing Rear caliper pistons

    i had to borrow that tools from Part Source as needle nose wont' work at all. tried even bleeding the line. no success, but the caliper compressing tool works like a charm.. part source did charge me $200 for deposit though. but of coz, fully returned back... free tool rental, nice!
    2005 GS, Auto, A/C, Carbon Grey
    - Prolumen 5000k HID, Lighted Mazda 3 door sills, 2 tone colour, OEM fog lights with 2700k H11 fog bulbs
    - CompuStar Remote starter w/ trunk release
    - Mazda OEM Auto dimming mirror with compass, temperature, homelink, shark fin
    - RX8 18" Rim with General Exclaim UHP 225/40/18

  10. #10
    Jr Member 06Touring3's Avatar
    Join Date
    Jun 2006
    Age
    38
    Posts
    970
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Compressing Rear caliper pistons

    Needle nose can work....it just takes A LOTTTTTTTT to get it to compress (even when bleeding)....it was probly a solid 45 mins of work to get mine to compress with needle nose
    '06-3iTE-5Spd
    TWM|EBC|Prolumen|Simota|Progress|Fast

    20%-Tint|Broken-Fogs|Indy-Fogs|Moldingless|Stubby

  11. #11
    Newbie Halogen's Avatar
    Join Date
    Dec 2008
    Posts
    153
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Compressing Rear caliper pistons

    Wouldn't using a C clamp with a large washer or piece of wood over the piston work also ?

  12. #12
    Sr Member Soyabean's Avatar
    Join Date
    Oct 2007
    Age
    37
    Posts
    3,150
    Thanks
    38
    Thanked 18 Times in 12 Posts
    Mentioned
    9 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Compressing Rear caliper pistons

    Quote Originally Posted by Halogen View Post
    Wouldn't using a C clamp with a large washer or piece of wood over the piston work also ?
    Thats what I do, but why are u bringing up this thread from last year?

  13. #13
    Jr Member 5_Alive's Avatar
    Join Date
    Aug 2008
    Location
    Windsor, Ontario
    Posts
    994
    Thanks
    17
    Thanked 9 Times in 8 Posts
    Mentioned
    4 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Compressing Rear caliper pistons

    On the Protege's with the rear discs, there was a 10mm bolt I believe on the back-side of the rear caliper. You had to remove this to access an allen screw. Then you'd simply turn it I believe counter-clockwise and the piston would retract. When ready to install new pads, you just put the caliper on, tightened down the allen screw, and then re-installed the bolt.
    If the 3 is different and you need a turn tool, weird? Cause the Protege's also had the "two prongs" for that tool, and it definitely didn't work that way.
    From the South- Windsor
    Windsor Mazda Service Advisor
    2007 Mazdaspeed3-SOLD
    2012 MS3 CWP- SOLD but not forgotten
    2016 SWP Mazda6 GT 6-MT- DAILY

Similar Threads

  1. Rear shocks blown.
    By alhope34 in forum MazdaSpeed 3 Forum
    Replies: 34
    Last Post: 07-29-2011, 06:08 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •