Clunking front suspension

[horto]

Car has been at QEW Mazda most of the week with the front suspension ripped apart. Replaced bump stops, bearings, end links and threw in 2 new OEM front shocks for shits and giggles (and because SSG still hasn't got my koni's... 8+ months and counting). front end is still clunking when going over bumps and rough pavement. What else could it be? Tie rod/lower control arm? Ball joints are still good. 130k km on the car.

[Thrizzl3]

are you on the stock sway bars? i have the same issue...

[alhope34]

Sway bar bushings fix all.

Had to change my front bushings twice and rears once. Removed all clunking both times I changed them.

[Darkice]

Check ur brakes i know my rear ones clunk when that little pin is gone from the pads

[breakfasteatre]

Car has been at QEW Mazda most of the week with the front suspension ripped apart. Replaced bump stops, bearings, end links and threw in 2 new OEM front shocks for shits and giggles (and because SSG still hasn't got my koni's... 8+ months and counting). front end is still clunking when going over bumps and rough pavement. What else could it be? Tie rod/lower control arm? Ball joints are still good. 130k km on the car.

are you paying for all of that or is it somehow covered under warranty?

[horto]

Sway bar bushings fix all.

Had to change my front bushings twice and rears once. Removed all clunking both times I changed them.

Pretty sure those were replaced w/ end links. Will double-check.

are you paying for all of that or is it somehow covered under warranty?

Not covered under warranty I just can't stand the sound anymore!

[Fobio]

hey horto...long time no see/chat!

I got my front sway bar bushing replaced ...I got them for under $30 a pair @ SpeedStar as per advise from Donutz/Jason...what FSB are you runng?

[alhope34]

Pretty sure those were replaced w/ end links. Will double-check.

They werent when I had my end links replaced under warranty for the same noise and didnt fix it. Get them changed!!!!!!

[horto]

Vince - yeah, life/work has been super busy lately. We need another wings meet I'm running all stock suspension including FSB.

Al - you were right, the bushings hadn't been replaced, they were done and now the noise is gone.

[alhope34]

^^ Excellent! Glad to hear.

[speedsilver]

im having the same issue, and i had a strut replaced when i got the car, now ill try this, thanks! (a lot less expensive of a fix than i thought )

[Murrayspeed]

I had the same problem so i replaced the swar bar end links. Its fixed it for a few weeks then i broke my passangers side control arm. Fixed that then blew a strut. Then said screw it and did Tien super street coilovers all around. Workin like a peach since then haha

[SickoS2K]

I had the same problem so i replaced the swar bar end links. Its fixed it for a few weeks then i broke my passangers side control arm. Fixed that then blew a strut. Then said screw it and did Tien super street coilovers all around. Workin like a peach since then haha

[AHickman]

sounds like a pain in the ass

[krimsalt]

Sway bar bushings fix all.

Had to change my front bushings twice and rears once. Removed all clunking both times I changed them.

This is most often the issue. And it seems the only one left. A-arm (or control arm, whatever you want to call it) as well as sway bar end linkages, and stabilyzer links could be bad. Try the sway bar links first

[joedemarco]

so what I think could be leaky shocks...may very well just be sway bar bushings...I'll have to get those changed.

Anyone know where I should get them? contact info?

Thanks

[alhope34]

Get them from the dealer. They are cheap.

[-ToM-]

ya i got the same problem here, would maybe tightening the bushing work ?

[alhope34]

Just replace them, they are cheap so you shouldn't be. I don't think they are something you can really "tighten" anyway.

[Wild Weasel]

Hey... are there any better urethane bushings or something so they don't need to be replaced again in a couple years?

And how tough is this to do in a driveway? I expect the rear ones are easy. What about the fronts?

[dexter]

I had a shop do the fronts on mine last year because we didn't know the source of the clunk and it ended up being the bushings that fixed it. The rears I just swapped out a couple weeks ago and can be done in about an hour in the drive way. Super easy install. The bushing may look intact but they seem to get as hard as plastic over time which is probably the cause of many clunks. Both my fronts and rears looked fine, replaced both and both times it stopped a clunk.

[betterthansx]

Anyone know how much the shops charge to change the bushing? It is a $30.00 but if it is $500 in labor to replace it, I will try to do it myself!

[SomeGuy]

Anyone know how much the shops charge to change the bushing? It is a $30.00 but if it is $500 in labor to replace it, I will try to do it myself!

FSB bushings are several hours work...the parts are cheap but getting them in/out is a pain in the ass.

[betterthansx]

FSB bushings are several hours work...the parts are cheap but getting them in/out is a pain in the ass.

I just YouTubed it (should have done that first) and it looks like you have to drop the whole front subframe...damn

Might as well replace the swaybars while I'm at it!

[SomeGuy]

I just YouTubed it (should have done that first) and it looks like you have to drop the whole front subframe...damn

Might as well replace the swaybars while I'm at it!

Yes you do, you might be able to snake a wrench in there but it's super tight and at least one of the bushing fasteners won't back all the way out from what I remember.

And yes you might as well do the FSB as a whole while you're at it.