Hopefully 'the shop' will do something.............at this point.....
Re: Snots - Rocket Build
Hopefully 'the shop' will do something.............at this point.....
0.000212524463 gigawatts
Re: Snots - Rocket Build
That I will find out tomorrow.....Originally Posted by Mr Wilson
Hole In Block Tuning! I'll give you HIB.
2010 MS3 Black395whp/386wtq
| Molnar Rods | CP-e Stage 2 Pistons | Much Head Work | ATP GTX3076 | Tial 38mm EWG | HTP 4 Inch Intake | BSD | Passenger and Rear MM | Denso ITV22's | OCC | Ultimate Racing TBE | Tredstone TR8C FMIC | Tial BPV | Autotech Internals | Grimmspeed ECBS 3 port | Te37 Volks| 245/45/17 Dunlop zzi tires| Cobb AP Self Street Tuned | Sonic Tuning CO's | stoptech breaks and slotted roters |
Re: Snots - Rocket Build
Crowbar? Looks like your head vented a rod
Hopefully you didn't get those 3 staples from "the shop"
Re: Snots - Rocket Build
The clearances off on my staples? Hahaha
Re: Snots - Rocket Build
You deserve better then this my friend.
Re: Snots - Rocket Build
Thank goodness he's a persistent bitch
If not snotrocket would have long ago become snot***kit
Re: Snots - Rocket Build
Oh man, that sucks! Looks like the bearing clearance was too tight. Its important to measure the bearing to journal clearance with a plastigauge when assembling the motor. Good luck man!
2011 MAZDASPEED3 Hypnotic Tuned - Rob
CPE HPFP - CPE Catted Downpipe - CPE Catback Exhaust - 3" ETS TMIC - Cobb RMM - AEM Boost Gauge & Vent Pod - CANBus Triple - Corksport BPV - Corksport hood strut - Corksport RSB - Corksport Short Shifter - HTP 3.5" Intake - Damond TMM - Damond Vented CC - Vented Oil Cap - Tokay v2 Seals - GTX3067R - Damond PCV Plate - Built Engine (Manley Rods, 88mm Supertech 4032 Piston) -
Re: Snots - Rocket Build
Ah damn dude! Shitty deal
Re: Snots - Rocket Build
Any updates on the rebuilt motor?
Re: Snots - Rocket Build
Based on photos I saw from last night, the engine might be in
Snots - Rocket Build
Where we are at
Re: Snots - Rocket Build
Right on. So what did you do to fix the toast rebuilt engine? Did you just replace the parts or do a fresh rebuild again?
Re: Snots - Rocket Build
He's decided to go with a B18c now.
Re: Snots - Rocket Build
FYHN! lol...
Glad to see that this build is back on track. Made me sad to hear about the engine pooping out from a bad bearring clearance or whatever happened.
Re: Snots - Rocket Build
K20 with KraftWerks supercharger is where it's at
Re: Snots - Rocket Build
All I can say is that you have to make sure the bearing clearance on the crank is within spec (plasti gauge) and measure the cam to tappet clearance. If anything is too tight or loose major fail soon follows.
Snots - Rocket Build
Had to over bore, thus new over bore pistons. One new rod. New cams. Had to Line hone the head. Pretty well started fresh, not fun......
Re: Snots - Rocket Build
That sucks, well I hope this new build works out for you and you can start to enjoy the car again.
Re: Snots - Rocket Build
whats the update with the build?
Forged - Overbore - BNR S3 Turbo - Meth -
*** Tuned 348whp/414wtq
Stratified tuning currently… Numbers coming soon
Re: Snots - Rocket Build
@Snotrocket ^
Re: Snots - Rocket Build
Updates for this build can be found at:
http://www.mazdaspeedforums.org/foru...-build-129112/
Re: Snots - Rocket Build
should you not worry about your build more and less about his?
Re: Snots - Rocket Build
my build is going great im not worried at all lolshould you not worry about your build more and less about his?
Re: Snots - Rocket Build
Until you spin a rod bearing.
Re: Snots - Rocket Build
wont happenUntil you spin a rod bearing.
Posting Permissions
Reply With Quote
