Results 1 to 8 of 8

Thread: MAF Calibration on ots intake specific maps

  1. #1
    Noob Astromax's Avatar
    Join Date
    May 2014
    Location
    Sudbury ON
    Age
    42
    Posts
    15
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default MAF Calibration on ots intake specific maps

    Sorry if this is a noob question, been looking through threads on tm3 and msf for an hour already without finding an answer.

    I have the corksport sri+tip on my speed. I just got the v3 accessport and applied the corksport stage 1+sri ots map. Is it still required to scale the entire map due to difference in housing size over stock? Or would the intake specific map already have that scaling done and only require tweaking each breakpoint set based on my datalogs?

    Of the top of my head my first good log reading was showing approximately -12.5, -7.6, -5.4, -1.6.

    Thanks

  2. #2

    Join Date
    Mar 2009
    Location
    Kitchener
    Posts
    5,736
    Thanks
    213
    Thanked 1,156 Times in 643 Posts
    Mentioned
    295 Post(s)
    Tagged
    0 Thread(s)

    Default Re: MAF Calibration on ots intake specific maps

    The OTS maps are a starting point and have a rough calibration. However every MAF sensor (and o2 sensor, etc) is a little different which leads to slight variations intake to intake, car to car, and hence the need for a MAF calibration.

    If you have LTFT's that aren't within +/- 3 or so, you should be doing a round or two of MAF calibration. If those -12.5, -7.6, -5.4, -1.6 are your LTFT values, you definitely need to do a calibration.

    - 2021 Porsche Macan GTS -
    - 2016 Lexus NX200t F Sport -
    - 2010 Mazdaspeed 3 Black Mica - SOLD -

  3. #3
    Noob Astromax's Avatar
    Join Date
    May 2014
    Location
    Sudbury ON
    Age
    42
    Posts
    15
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: MAF Calibration on ots intake specific maps

    So should I still start by scaling the entire map by 1.313 (3" corksport vs stock) then adjusting each breakpoint set?

  4. #4

    Join Date
    Mar 2009
    Location
    Kitchener
    Posts
    5,736
    Thanks
    213
    Thanked 1,156 Times in 643 Posts
    Mentioned
    295 Post(s)
    Tagged
    0 Thread(s)

    Default Re: MAF Calibration on ots intake specific maps

    Exactly which intake do you have?

    Exactly which map are you using?

    Give us links to both...it's kind of important.

  5. #5
    Banned
    Join Date
    Apr 2010
    Location
    Projects
    Ride
    another mazda
    Posts
    1,976
    Thanks
    67
    Thanked 261 Times in 121 Posts
    Mentioned
    51 Post(s)
    Tagged
    0 Thread(s)

    Default Re: MAF Calibration on ots intake specific maps

    In for HIB

  6. #6
    Noob Astromax's Avatar
    Join Date
    May 2014
    Location
    Sudbury ON
    Age
    42
    Posts
    15
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

  7. #7

    Join Date
    Mar 2009
    Location
    Kitchener
    Posts
    5,736
    Thanks
    213
    Thanked 1,156 Times in 643 Posts
    Mentioned
    295 Post(s)
    Tagged
    0 Thread(s)

    Default Re: MAF Calibration on ots intake specific maps

    Ok so you don't have the 3" intake, you have a normal stock sized MAF housing intake. There is no scaling necessary, just do a MAF cal.

  8. #8
    Noob Astromax's Avatar
    Join Date
    May 2014
    Location
    Sudbury ON
    Age
    42
    Posts
    15
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: MAF Calibration on ots intake specific maps

    Alright sounds good, thanks for the help

Similar Threads

  1. 19 AFR at Idle with JBR intake (even after MAF Calibration)
    By pwdunmore in forum MazdaSpeed3 Tuning
    Replies: 5
    Last Post: 10-21-2012, 06:57 PM
  2. JBR Intake MAF Cal and Map
    By pwdunmore in forum MazdaSpeed3 DISI General Powertrain
    Replies: 6
    Last Post: 10-04-2012, 12:55 PM
  3. MAF calibration question
    By Elusivellama in forum MazdaSpeed3 Tuning
    Replies: 2
    Last Post: 03-26-2012, 02:00 PM
  4. Need help with Intake MAF
    By Spoolin in forum MazdaSpeed 3 Forum
    Replies: 27
    Last Post: 03-24-2011, 01:40 PM
  5. Official Cobb 1.03 OTS Maps
    By Fobio in forum MazdaSpeed3 Modifications
    Replies: 30
    Last Post: 03-16-2009, 03:13 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •