Where are you located? I'm interested in buying the JBR for my Tripoint rear sways and perhaps we can save on shipping if putting an order together. The flimsy bracket that came with it had seen better days....
Where are you located? I'm interested in buying the JBR for my Tripoint rear sways and perhaps we can save on shipping if putting an order together. The flimsy bracket that came with it had seen better days....
|-----> Roof Rack <-----| Thule Base Rack - Rocky Mounts Bike Tray - Thule Ski Holder
2007 GT Sedan 5spd CWP | Rays Mazdaspeed Wheels | Tri-Point Engineering Rear Swaybar
SPC Camber Links | Bilstein Coilovers | Tint | LED Brake
MSpeed might put together a "save on shipping" order in the summer? @Fobio
I went back to OEM sway bar, no joke. I did not want to deal with poorly engineered / sourced shit breaking on me. Brackets broke twice (corroded through), sway bar was losing its fight with winter (powder coat was cracking off at the seams and edges).
I had the opportunity to see the OEM sway bar on another guy's speed 3 (2011 model) and it had no signs of wear, no rust, nothing. This as on the same day that Jimmy had my car up on the hoist for an oil change, same day I placed an order for a new OEM bar and brackets.
Last edited by Elusivellama; 02-22-2015 at 10:41 AM.
fywdyl (02-22-2015)
Elusivellama (02-22-2015)
Don't forget those steel locating collars. Mine were rusted all over and dripping rust juice from every orifice, and I lost one set a few months after the sway bar was installed. Just looked under my car one day to check on things and the bottom half of the collar on the passenger side was missing. I ended up going to Spanauer in Kitchener and buying identical brackets for $20 and reinstalling again. Then my bracket broke again for the 2nd time and that was when I ejected that piece of shit from my car.
The sway bar should have been manufactured from a single bar of steel and not TIG welded together from 3 pieces - I don't care what people say, welds will always be weaker than a contiguous length of steel. Next, those locating collars should have been put into their proper locations from the shop, and the material should have been something like a stainless steel band crimped over the bar (see pic below). The brackets should have been this thick:
Finally coat the **** out of everything with layers of thick primer and paint, not powder coat (which is a thin layer of plastic, and plastic doesn't do well in cold temps and high stress).
Last edited by Elusivellama; 02-22-2015 at 10:59 AM.
FYI - the newer CS sway bar and a couple others out there are a single continuous piece now.
I wonder what is up with these cars eating RSB/components though...I mean I haven't snapped or broken anything like you guys but I had my old CS bar bend, I've replaced one set of rusted to shit collars, I am on my third set of brackets (although all of them are still usable and one set is just because I got a new bar). I question why shit is actually breaking which I suspect might be from other components still...but they definitely don't seem to be holding up.
Then again, pay to play and at least RSB's are cheap lol
- 2021 Porsche Macan GTS -
- 2016 Lexus NX200t F Sport -
- 2010 Mazdaspeed 3 Black Mica - SOLD -
im on my second cs bar now as well as mine snapped in half a year or two ago lol. i just took a look at the collars currently on the car, and they dont look the greatest. decided im going to try the jbr competition as im not able to oversteer with the cs bar maxed out with dampening on full stiff in the rear. rsbs cost enough that you dont want to be buying one every year or two.
"There is no path to happiness: Happiness is the path " ~Buddha
"And so you touch this limit, something happens and you suddenly can go a little bit further. With your mind power, your determination, your instinct, and the experience as well, you can fly very high." - Ayrton Senna
"There is nothing noble in being superior to your fellow man: true nobility is being superior to your former self" -Ernest Hemingway
http://corksport.com/mazda-billet-sw...-brackets.html i have these
http://www.corksport.com/blog/corksp...aybar-bracket/ Read the blog.
2010 GT MZ3 2.5 MSDS Headers, Custom Tune, CS SRI,CS Full CBE,CS LED conversion, 3K HID fogs, 15%Tints,Koni Str.T H&R Sport Lowering Springs, Speed3 Rims, duel 12''MTX subs, Vinyl Wrap Roof,Mirrors,Spoiler
fywdyl (02-23-2015)
I might need a bracket too, it sounds like mine is broken from what I heard driving to work this morning. I'll check under tonight, might order soon..
GB?
Not ordering a sway bar, just the brackets..
From JBR's site...
Specifications Simulating 1" of body roll:
Stock Sway Bar setting:
MAZDASPEED 3 is 479 lbs/in
MAZDA 3 & 5 is 228 lbs/in
JBR 3-Way Adjustable Sway Bar Settings:
Stiff setting is 593 lbs/in
Stiffer Setting is 718 lbs/in
Stiffest Setting is 901 lbs/in
The fact that we are asking the car and it's components to deal with between 2 and 4 times the amount of stress they were originally designed for is probably part of the reason...
Has anyone who is having issues checked for excessive pre-load on the sway bar when at static ride height ? Do you park the car on uneven surfaces ? Either of those could cause the bar and the brackets to be loaded more than usual and lead to premature wear/fatigue/failure...
Sorry to revive the thread, but my jbr bracket broke today =(, called Jimmy, he told me to use cloth hanger to tie the bar to the body for now.
I am planning to get the http://www.jamesbaroneracing.com/sho...2nu4mde470o6g0
I know it's more expensive, but I hate to have it break again.
There's probably no warranty for my existing ones right? given that it seems like a common issue.
He won't warranty the bracket if it rusted through. If it broke from normal use, he may.
2010 Black Mazdaspeed 3 - Lightly modded
Replaced the brackets with the big hunks o' steel yday. Feels good to drive a normal car again. Hopefully I don't have to get under there again to fix anything anymore.
optiklenz13 (04-13-2015)