Results 1 to 6 of 6

Thread: Meth nozzle size!?

  1. #1
    Jr Member tanspeed3's Avatar
    Join Date
    Jul 2012
    Location
    Peterborough
    Age
    35
    Posts
    398
    Thanks
    112
    Thanked 134 Times in 97 Posts
    Mentioned
    62 Post(s)
    Tagged
    0 Thread(s)

    Default Meth nozzle size!?

    I'd like to hook up a meth kit this summer once I drop in my built engine. Need some insight into wmi nozzle size. Should be able to reach the mid 500whp mark on 94 and meth with my setup. I've followed a few other builds in the states and have shown some serious power without aux fuel. So let's see what we can figure out

    Thanks in advance!

    T
    400WHP Club!
    Gingerbuilt-Self Tuned-Built Short Block yada yada yada-Enkie RPF1 17x9 +45 wrapped with 245/40 PSS

    Check out my build thread! http://www.torontomazda3.ca/forum/sh...s-Build-Thread

  2. #2
    Sr Member Kiyomi's Avatar
    Join Date
    Jul 2010
    Age
    33
    Posts
    4,162
    Thanks
    205
    Thanked 453 Times in 259 Posts
    Mentioned
    116 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Meth nozzle size!?

    what % of meth/water you plan on using?
    "There is no path to happiness: Happiness is the path " ~Buddha

    "And so you touch this limit, something happens and you suddenly can go a little bit further. With your mind power, your determination, your instinct, and the experience as well, you can fly very high." - Ayrton Senna

    "There is nothing noble in being superior to your fellow man: true nobility is being superior to your former self" -Ernest Hemingway

  3. #3
    Jr Member tanspeed3's Avatar
    Join Date
    Jul 2012
    Location
    Peterborough
    Age
    35
    Posts
    398
    Thanks
    112
    Thanked 134 Times in 97 Posts
    Mentioned
    62 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Meth nozzle size!?

    Fiddy/fiddy

  4. #4
    Jr Member tanspeed3's Avatar
    Join Date
    Jul 2012
    Location
    Peterborough
    Age
    35
    Posts
    398
    Thanks
    112
    Thanked 134 Times in 97 Posts
    Mentioned
    62 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Meth nozzle size!?

    Perhaps some in tank meth for a hot map

  5. #5
    Member
    Join Date
    May 2012
    Posts
    1,431
    Thanks
    30
    Thanked 165 Times in 115 Posts
    Mentioned
    53 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Meth nozzle size!?

    You are gonna need somewhere around 800cc/min of additional fueling. That is assuming out stock injectors are 1200 cc.

    I think that leaves you the option of two d10 or maybe one d14 depending on your IDC.

    How are you injecting it? Throttle body plate?

  6. #6
    Member
    Join Date
    May 2012
    Posts
    1,431
    Thanks
    30
    Thanked 165 Times in 115 Posts
    Mentioned
    53 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Meth nozzle size!?

    http://edgeautosport.com/manufacture...d-6-2006-2013/

    There is actually some info on the stock injector capacity and fueling in the description of this fueling kit.

Similar Threads

  1. snow performance meth nozzle adapter needed ASAP
    By mikey32235 in forum MazdaSpeed 3 Forum
    Replies: 2
    Last Post: 04-04-2014, 01:17 PM
  2. Windshield washer nozzle adjustement?
    By ipse in forum Mazda3 General Discussion
    Replies: 26
    Last Post: 03-03-2012, 10:57 PM
  3. Frozen Fluid Nozzle?
    By UncleIstvan in forum Problems with the Mazda3
    Replies: 23
    Last Post: 11-30-2007, 03:56 PM
  4. rear washer nozzle
    By ultimateM3 in forum Problems with the Mazda3
    Replies: 2
    Last Post: 04-19-2006, 10:47 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •