Page 1 of 2 12 LastLast
Results 1 to 25 of 29

Thread: Clunking front driver side when turning over bumps

  1. #1
    Newbie
    Join Date
    Feb 2015
    Posts
    102
    Thanks
    10
    Thanked 7 Times in 7 Posts
    Mentioned
    3 Post(s)
    Tagged
    0 Thread(s)

    Default Clunking front driver side when turning over bumps

    Hi guys,

    Recently Iíve been hearing a clunk when Iím turning right and at the same time going over bumps from the front driver side wheel area. Any ideas?

    Also hearing a clunking sound at the rear when Iím driving around 20-40km/h over bumps but seems to be gone when I drive over 60km.

    Iíll be jacking up the rear this weekend to check if anything is loose or so.

    Recently had a set of Koni oranges and Eibach Prokits installed - only issue I had was the top nut was loose which has been resolved.

    Thanks a bunch


    Sent from my iPhone using Tapatalk

  2. #2
    Newbie LiviuTincu's Avatar
    Join Date
    Nov 2010
    Posts
    211
    Thanks
    0
    Thanked 19 Times in 15 Posts
    Mentioned
    5 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    It might be the ball joint or upper strut mount. What mileage is the car?

    Sent from my Moto G4+ using Tapatalk

  3. #3
    Newbie
    Join Date
    Oct 2014
    Location
    Orillia
    Posts
    228
    Thanks
    5
    Thanked 24 Times in 21 Posts
    Mentioned
    4 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    Front will most likely be a ball joint or sway bar end link. It could very well be a strut mount if you re used yours when you swapped things over. They can't be re used from mine and many others experience. The rear could also be an endlink. So many bushings in the rear it can be difficult to diagnose.

  4. #4
    Newbie
    Join Date
    Feb 2015
    Posts
    102
    Thanks
    10
    Thanked 7 Times in 7 Posts
    Mentioned
    3 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    Car is currently at 163k. The strut mounts were reused at both ends. Can the replacement be DYI? I wouldnít mind doing the work if itís straight forward.

    And where can I get proven replacement for them?

    Thanks for the reply guys


    Sent from my iPhone using Tapatalk

  5. #5
    Newbie
    Join Date
    Oct 2014
    Location
    Orillia
    Posts
    228
    Thanks
    5
    Thanked 24 Times in 21 Posts
    Mentioned
    4 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    Could easily be the strut mounts, check the other stuff first. A DIY requires spring compressors which is a fairly cheap tool. I did mine, didn't redo the alignment after and had no issues. Set aside 4 hours if you have never done it before. The most difficult part is sliding the bottom of the strut into the slot. Know how to properly remove an endlink before you attempt.

  6. #6
    Newbie
    Join Date
    Feb 2015
    Posts
    102
    Thanks
    10
    Thanked 7 Times in 7 Posts
    Mentioned
    3 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    Yeah I figured I should get the struts replaced.

    Amazon has the rear strut mounts as ĎDorman 924-412í and I tried using their car fit function but it tells me it doesnít fit my car. Where can I check part number that would fit my car?

    Btw I have 2012 hatchback 2.5L

    Thanks again


    Sent from my iPhone using Tapatalk

  7. #7
    Newbie LiviuTincu's Avatar
    Join Date
    Nov 2010
    Posts
    211
    Thanks
    0
    Thanked 19 Times in 15 Posts
    Mentioned
    5 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    I would not buy Dorman , KYB is better for rear mounts. But these when damaged will make a very loud noise and you will know that the mount is broken. Maybe the end links are loose, trailing arm bushing is out, check first to see what the problem is. Control arm bushing could also be the problem.

    Sent from my Moto G4+ using Tapatalk
    Last edited by LiviuTincu; 11-09-2018 at 01:42 PM.

  8. #8
    Newbie
    Join Date
    Feb 2015
    Posts
    102
    Thanks
    10
    Thanked 7 Times in 7 Posts
    Mentioned
    3 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    Rockauto is listing brands Sachs at 20$ each and Mevotech at 40$ each.

    Not sure what everybody goes with when it comes to replacing the strut mounts

    I called Mazda and they donít sell the rear strut mounts separately.


    Sent from my iPhone using Tapatalk

  9. #9
    Moderator S.F.W.'s Avatar
    Join Date
    Oct 2004
    Location
    North York
    Age
    39
    Posts
    17,997
    Thanks
    923
    Thanked 1,353 Times in 703 Posts
    Mentioned
    398 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    Quote Originally Posted by KevinM3 View Post
    Rockauto is listing brands Sachs at 20$ each and Mevotech at 40$ each.

    Not sure what everybody goes with when it comes to replacing the strut mounts

    I called Mazda and they don’t sell the rear strut mounts separately.


    Sent from my iPhone using Tapatalk
    I have read good things about Sachs with regard to the Mazdaspeed3. I am going that route for my MS3.
    2010 Black Mazdaspeed 3 - Lightly modded

  10. #10
    Newbie
    Join Date
    Feb 2015
    Posts
    102
    Thanks
    10
    Thanked 7 Times in 7 Posts
    Mentioned
    3 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    Quote Originally Posted by S.F.W. View Post
    I have read good things about Sachs with regard to the Mazdaspeed3. I am going that route for my MS3.
    Yeah I read likewise. Unfortunately, Rockauto only has 1 left of the Sachs, and with additional 10$ to ship here by Dec 3 lol

    I'll keep looking around

  11. #11
    Newbie
    Join Date
    Oct 2014
    Location
    Orillia
    Posts
    228
    Thanks
    5
    Thanked 24 Times in 21 Posts
    Mentioned
    4 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    Oh if it was the strut mounts in the rear you would know. Your car would sound deadly unsafe. Had it happen to me last year.

  12. #12
    Newbie
    Join Date
    Feb 2015
    Posts
    102
    Thanks
    10
    Thanked 7 Times in 7 Posts
    Mentioned
    3 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    Quote Originally Posted by jeff7670 View Post
    Oh if it was the strut mounts in the rear you would know. Your car would sound deadly unsafe. Had it happen to me last year.
    I had a quick check last week when i put my winters on, and the strut mounts looked fine. I suspect the single nut holding the strut bolt to the mounts on the top is loose.

  13. #13
    Newbie LiviuTincu's Avatar
    Join Date
    Nov 2010
    Posts
    211
    Thanks
    0
    Thanked 19 Times in 15 Posts
    Mentioned
    5 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    Quote Originally Posted by KevinM3 View Post
    I had a quick check last week when i put my winters on, and the strut mounts looked fine. I suspect the single nut holding the strut bolt to the mounts on the top is loose.
    You don't need to change the mount if the nut is loose. Are you sure are not the brake pads? Press the brake next time and see if the clunk goes away.

    Sent from my Moto G4+ using Tapatalk

  14. #14
    Newbie LiviuTincu's Avatar
    Join Date
    Nov 2010
    Posts
    211
    Thanks
    0
    Thanked 19 Times in 15 Posts
    Mentioned
    5 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    These are to be installed this weekend, brrrrrrr.

    Sent from my Moto G4+ using Tapatalk

  15. #15
    Newbie
    Join Date
    Feb 2015
    Posts
    102
    Thanks
    10
    Thanked 7 Times in 7 Posts
    Mentioned
    3 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    Quote Originally Posted by LiviuTincu View Post
    You don't need to change the mount if the nut is loose. Are you sure are not the brake pads? Press the brake next time and see if the clunk goes away.

    Sent from my Moto G4+ using Tapatalk
    If I can recall, Iím already on the brakes when Iím slowing down and the clunks come on when going over even little bumps on the road


    Sent from my iPhone using Tapatalk

  16. #16
    Newbie LiviuTincu's Avatar
    Join Date
    Nov 2010
    Posts
    211
    Thanks
    0
    Thanked 19 Times in 15 Posts
    Mentioned
    5 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    Finished on Saturday, 4 hours to install.

    Sent from my Moto G4+ using Tapatalk

  17. #17
    Newbie dadinho_nfg's Avatar
    Join Date
    Jul 2009
    Posts
    234
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Mentioned
    2 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    Having the exact same noise happening. Driving a 08 speed3 with 62k km. Car was bought two years ago from original owner who winter stored it every winter.

    Took the car to Daleyís Auto in Streetsville twice now and they canít seem to locate the issue. Troy ( the owner ) suggested maybe if the car was t stored on blocks perhaps it can be the shocks / struts. He did check the mounts and no issues there.

    Iím looking around for an oem swap. Car is bare bone stock and not looking to lower or anything. Iím considering Koni srt or even yellows.

    Interested to see what you all land on and what the root cause is.
    Dadinho

  18. #18
    Newbie dadinho_nfg's Avatar
    Join Date
    Jul 2009
    Posts
    234
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Mentioned
    2 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    What are those parts and how much from Mazda?

  19. #19
    Newbie LiviuTincu's Avatar
    Join Date
    Nov 2010
    Posts
    211
    Thanks
    0
    Thanked 19 Times in 15 Posts
    Mentioned
    5 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    My front left side brake pads rattle, sooooo annoying. I have to open it up and fix it.

    Sent from my Moto G4+ using Tapatalk

  20. #20
    Newbie
    Join Date
    Feb 2015
    Posts
    102
    Thanks
    10
    Thanked 7 Times in 7 Posts
    Mentioned
    3 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    Havenít had the chance to check the car but the fronts I suspect itís the end links.

    The rear I believe are the sway bar end links also


    Sent from my iPhone using Tapatalk

  21. #21
    Newbie LiviuTincu's Avatar
    Join Date
    Nov 2010
    Posts
    211
    Thanks
    0
    Thanked 19 Times in 15 Posts
    Mentioned
    5 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    Quote Originally Posted by dadinho_nfg View Post
    What are those parts and how much from Mazda?
    $200 from Mazda , each , without tax . They are the control arms .

  22. #22
    Sr Member Flagrum_3's Avatar
    Join Date
    May 2005
    Location
    Scarborough
    Posts
    6,202
    Thanks
    335
    Thanked 327 Times in 261 Posts
    Mentioned
    97 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    Quote Originally Posted by LiviuTincu View Post
    $200 from Mazda , each , without tax . They are the control arms .
    After my 2nd Moog Lower Control arm bit the dust, I went back to OEM and picked up, just recently, a LCA at Ajax Mazda for $174 with the TM3 discount. Its worth the extra coin as the quality is apparent. The Mazda LCA is so much more robust.


    _3

  23. #23
    Newbie LiviuTincu's Avatar
    Join Date
    Nov 2010
    Posts
    211
    Thanks
    0
    Thanked 19 Times in 15 Posts
    Mentioned
    5 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    Quote Originally Posted by Flagrum_3 View Post
    After my 2nd Moog Lower Control arm bit the dust, I went back to OEM and picked up, just recently, a LCA at Ajax Mazda for $174 with the TM3 discount. Its worth the extra coin as the quality is apparent. The Mazda LCA is so much more robust.


    _3
    Yes, OEM is holding a lot better than aftermarket. I have got mine from UAE, $320 all in.

    Sent from my Moto G4+ using Tapatalk

  24. #24
    Newbie LiviuTincu's Avatar
    Join Date
    Nov 2010
    Posts
    211
    Thanks
    0
    Thanked 19 Times in 15 Posts
    Mentioned
    5 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    I was wrong about the brake pads making noise , it was the sway bar Link. Very annoying rattle, I'll fix it this week.

    Sent from my Moto G4+ using Tapatalk

  25. #25
    Newbie
    Join Date
    Feb 2015
    Posts
    102
    Thanks
    10
    Thanked 7 Times in 7 Posts
    Mentioned
    3 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Clunking front driver side when turning over bumps

    Quote Originally Posted by LiviuTincu View Post
    I was wrong about the brake pads making noise , it was the sway bar Link. Very annoying rattle, I'll fix it this week.

    Sent from my Moto G4+ using Tapatalk
    How much did you get the front links from Mazda?




    Sent from my iPhone using Tapatalk

Page 1 of 2 12 LastLast

Similar Threads

  1. Clunking noise up to 15 kmh over bumps
    By redstar1 in forum Problems with the Mazda3
    Replies: 3
    Last Post: 07-27-2017, 09:59 PM
  2. Clunk while turning right over bumps
    By Milan96 in forum Suspension & Brakes
    Replies: 12
    Last Post: 01-03-2016, 06:38 PM
  3. Hitting bumps and Left front side craps out
    By AHickman in forum I.C.E (In-Car Entertainment)
    Replies: 3
    Last Post: 04-19-2012, 12:49 AM
  4. Clunking noise from the driver's side
    By Tuga in forum Problems with the Mazda3
    Replies: 7
    Last Post: 08-11-2009, 11:33 PM
  5. Driver side HID turning on after passenger
    By Fuman in forum Lighting, Electrical & Security
    Replies: 5
    Last Post: 03-08-2008, 05:03 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •