-
Re: mikey32235's ride thread
Quote:
Originally Posted by
schmat66
my nrg hub fits over my clock spring... did you end up losing your turn signal auto off things?
my NRG hubs center bore is too small for my momo wheel to fit the horn so i returned it at bought the momo hub. had to remove clock spring, yea clicky thing is gone lol but i dont mind.
-
Re: mikey32235's ride thread
question...
today i was doing a WOT and i felt some mis-firing, sure enough i got the code random misfire... i have a feeling it has to do with the purge valve solenoid that needs replacing. any thoughts?
-
Re: mikey32235's ride thread
Quote:
Originally Posted by
mikey32235
question...
today i was doing a WOT and i felt some mis-firing, sure enough i got the code random misfire... i have a feeling it has to do with the purge valve solenoid that needs replacing. any thoughts?
Didn't you say this in the random MS3 thread? I think you could be right but there is only one way to tell lol... Could be old plugs but I would think you have new ones in your engine since it's new.
-
Re: mikey32235's ride thread
Quote:
Originally Posted by
pwdunmore
Didn't you say this in the random MS3 thread? I think you could be right but there is only one way to tell lol... Could be old plugs but I would think you have new ones in your engine since it's new.
i meantioned the purge valve in random lol, not this this is a new update from today :P the plugs only had 10,000km on it they were the IVT22's... not sure if one is defective or not, it drives fine even when theres boost its good, i only had it happen once and i have no idea why. probalby gonna starrt with the purge valve and go from there
-
Re: mikey32235's ride thread
Quote:
Originally Posted by
mikey32235
i mentioned the purge valve in random lol, not this this is a new update from today :P the plugs only had 10,000km on it they were the IVT22's... not sure if one is defective or not, it drives fine even when there's boost its good, i only had it happen once and i have no idea why. probably gonna start with the purge valve and go from there
Plugs only last ~12k in these cars when running more boost, I got to replace mine this year.
info link:
https://cobbtuning.zendesk.com/hc/en...ug-Information
-
Re: mikey32235's ride thread
hmm, never knew that! should i be putting in the 1 step colder. or two? will it effect my tune/performance if i go a step colder?
update: just ordered an oem purge valve solenoid from mazda.
-
Re: mikey32235's ride thread
Quote:
Originally Posted by
pwdunmore
not to take anything away from Cobb but I ran OEM, stock, from the factory NGK plugs in my engine for 90,000+ kms. Half of that was Stage 2 @ 20psi (no meth)
When they were pulled from the motor, they were still good and the gap across all of them were still within spec.
NGK > Denso
-
Re: mikey32235's ride thread
Quote:
Originally Posted by
MajesticBlueNTO
not to take anything away from Cobb but I ran OEM, stock, from the factory NGK plugs in my engine for 90,000+ kms. Half of that was Stage 2 @ 20psi (no meth)
When they were pulled from the motor, they were still good and the gap across all of them were still within spec.
NGK > Denso
i never had a problem with the oem, i still have the plugs. but my question is that if im tuned will it effect my car if i change plugs?
-
Re: mikey32235's ride thread
i changed the purge valve and the spark plugs the other day, everytime at startup (cold) the car feels like its misfiring for like 10 seconds then it stops. i havent gotten a code but its driving me nuts! anyone have an idea where to go next? i feel like it may be the coil pack but i dont wanna keep changing things if i dont know forsure. any ideas?
-
Re: mikey32235's ride thread
Quote:
Originally Posted by
mikey32235
i changed the purge valve and the spark plugs the other day, everytime at startup (cold) the car feels like its misfiring for like 10 seconds then it stops. i havent gotten a code but its driving me nuts! anyone have an idea where to go next? i feel like it may be the coil pack but i dont wanna keep changing things if i dont know forsure. any ideas?
Spray the top of each coil with a bit of water. One by one. If it acts up. Thats the bad one. Or check them for hairline cracks
-
Re: mikey32235's ride thread
Quote:
Originally Posted by
MajesticBlueNTO
not to take anything away from Cobb but I ran OEM, stock, from the factory NGK plugs in my engine for 90,000+ kms. Half of that was Stage 2 @ 20psi (no meth)
When they were pulled from the motor, they were still good and the gap across all of them were still within spec.
NGK > Denso
I still remember pulling them! i was amazed!
@mikey32235 Maybe your misfire is from your Nankangs not being able to take the torque?
-
Re: mikey32235's ride thread
Quote:
Originally Posted by
mikey32235
i changed the purge valve and the spark plugs the other day, everytime at startup (cold) the car feels like its misfiring for like 10 seconds then it stops. i havent gotten a code but its driving me nuts! anyone have an idea where to go next? i feel like it may be the coil pack but i dont wanna keep changing things if i dont know forsure. any ideas?
do you have the traction control on or off?
-
Re: mikey32235's ride thread
Quote:
Originally Posted by
MarineMazda
I still remember pulling them! i was amazed!
@
mikey32235 Maybe your misfire is from your Nankangs not being able to take the torque?
very funny.. havent had the misfiring from the last couple of cold startups so not sure if its gonna come back or not. I'm waiting for a code to come up.
-
Re: mikey32235's ride thread
Have you gapped your oil since you had the engine built?
-
Re: mikey32235's ride thread
Quote:
Originally Posted by
Snotrocket
Have you gapped your oil since you had the engine built?
pm'd
-
Re: mikey32235's ride thread
-
Re: mikey32235's ride thread
@mikey32235 Can you post a video of this happening? Maybe post up your map too so people can see what it looks like.
-
Re: mikey32235's ride thread
Quote:
Originally Posted by
rzapata
@
mikey32235 Can you post a video of this happening? Maybe post up your map too so people can see what it looks like.
His map may be locked if AccessTuner Pro was used.
A log would be useful if the logging is started right when the car starts
-
Re: mikey32235's ride thread
ive been trying to log but every time i want to it doesnt misfire at startup! ive done a WOT and no misfiring there. no clue what it could have been but if it comes back ill definately log
-
Re: mikey32235's ride thread
Quote:
Originally Posted by
MajesticBlueNTO
His map may be locked if AccessTuner Pro was used.
A log would be useful if the logging is started right when the car starts
Yup, I just remembered it was a custom tune. Oh well.
Mikey, try what MBNTO suggested. Just start logging every start up. You'd eventually catch it. Then we can figure it out better.
-
Re: mikey32235's ride thread
Quote:
Originally Posted by
rzapata
Yup, I just remembered it was a custom tune. Oh well.
Mikey, try what MBNTO suggested. Just start logging every start up. You'd eventually catch it. Then we can figure it out better.
will do! ive been trying lol.
-
Re: mikey32235's ride thread
hey guys, question about meth... lol
so my meth injection is working great, i just set up my low level monitor the other day and it works fine. at the same time i set up the injection status green light. but i just cant seem to get it to work! yes all of the wiring is done correctly, and the light bulb does work. my last option im assuming it is a bad ground? but im not sure. has anyone had this problem?
-
Re: mikey32235's ride thread
I had a problem with the wire taps I was using not cutting all the way through the insulation on the first shot/push through. This was on my signal wire tap not making contact with my MAF wire.
You might want to check all the connections that you tapped for the wiring because when I checked and reapplied them I was able to get all my status lights working.
-
Re: mikey32235's ride thread
Quote:
Originally Posted by
pwdunmore
I had a problem with the wire taps I was using not cutting all the way through the insulation on the first shot/push through. This was on my signal wire tap not making contact with my MAF wire.
You might want to check all the connections that you tapped for the wiring because when I checked and reapplied them I was able to get all my status lights working.
mines a boost kit, so it injects at 10psi. everytime it hits the boost target level its supposed to turn green. but nothing happens!
@pwdunmore
-
Re: mikey32235's ride thread
Quote:
Originally Posted by
mikey32235
mines a boost kit, so it injects at 10psi. everytime it hits the boost target level its supposed to turn green. but nothing happens!
@
pwdunmore
It's ****ed up.