Boring.....
Printable View
Boring.....
Ahahaha
You two go get a room...in Winnipeg!
I'm back in Toronto tonight....Quote:
Originally Posted by Fobio
You jelly?
About 1:30 in.
http://www.youtube.com/watch?v=RSDUc...yer_embedded#!
wtf? you were sexting me from another area code...Quote:
Originally Posted by loki
chk your email?
EDIT:...fack...wilson...I didn't get to see it at work tmr...thanks! I need to go for a drive...
Haven't checked email yet. Will take a look tonightQuote:
Originally Posted by Fobio
You know I roll....
There are no borders when it comes to sexting
Fack... I just realized that when I calibrated my MAF, I only did it for MAF Table A... I didn't copy the values over to MAF Table B. Time for new calibrations, or can I just load the map from my AP, copy the values, then flash it back?
edit: assuming there IS a MAF Table B for genpu....
That's fine. (if there is one)Quote:
Originally Posted by Elusivellama
No MAF B for Genpu.
Thanks guys... phew, I thought I had done something wrong (was reading Abilor's guide again). I'm about to do the other little things that Abilor recommends to do.
I wouldn't just jump on board with what Abilor's guide tells you to doQuote:
Originally Posted by Elusivellama
stuff has changes since that guide was made, even though the guide was not made that long ago...
For example... I would not neuter the load tables by setting them all at 2.5 load, instead, I'd change them to about +0.05 of what I log as calc load.Quote:
Originally Posted by loki
Ok guys hopefully you can help.. So when I installed the RMM and had it up on jacks I noticed my front driver side dunlop was wearing out on the inside so that leads me to believe my front camber is off most likely due to hitting a pothole recently. The reason I say recently is when the tires went on about a month ago they were all in good condition.
So I had an appointment at Mazda this morning and well they will not do the alignment due to the car being lowered..(That story is for another day). They also said they wouldn't recommend doing the alignment until I replace the front tire.
I am hoping that one of you guys might have an oem set lying around for the 2010's that you are willing to sell one tire (or donate :chuckle) as I don't want to spend the money on a new one because next year all 4 will need to be changed.
Any suggestions would be great
move the rim/tire to the back?Quote:
Originally Posted by 2zoom
Thinking outside of the box. :thumbsupQuote:
Originally Posted by zzz3
The wear on the inside of the tire is most likely due to excessive toe, not camber.Quote:
Originally Posted by 2zoom
^^^Agreed. Which dealer?
I know Dave Wood does a great job on alignments if wanting to stay the dealer route.
Went to Mazda of Brampton for the alignment. After texting with Paul he's gonna set up an appointment at Maple Mazda for me as he has contacts there.Quote:
Originally Posted by Mr Wilson
So, after driving the car one day after an OCC install (with a bunch of WOT pulls) and letting it sit overnight, I check the hoses to the OCC and to the PCV nipple and the intake manifold nipple. Everything looks tight and nothing is leaking.
http://i853.photobucket.com/albums/a...a/e6f064c4.jpg
Both hoses zip tied to a large radiator hose.
http://i853.photobucket.com/albums/a...a/6149c75f.jpg
Question, it's normal to see some of the black oil crap pooled at the very bottom of the curve in the top hose, right? (the hose which runs from the green PCV nipple down and by the oil filter then back up to the top nozzle on the catch can). In the pic below, the clear hose in the foreground is the hose running from the IM to the bottom nozzle of the OCC, directly in the middle of the pic you can just make out a portion of the top hose with some black crap in it)
http://i853.photobucket.com/albums/a...a/e3521a9c.jpg
i think mine is a lot dirtier than that...how long ago did you change the oil?
edit: http://www.torontomazda3.ca/forum/sh...034#post924034
you should just create an OCC thread, so that people can post stuff in there as well, instead of just dumping stuff in here
all this information will then get lost in here, and then it's useless
2 minus 29.5 hours till i pick up the poo