HellaFlush mazda3s?

[Tokic_o]

So I'm really curious. Are there any hellaflush mazda3s around here??? I'd really like to see some and know the specs of wheels + tires they are running..


post em up!!

[Hives]

I haven't seen personally. I know there is one on the BC forums. Looks alrite, but I do not think it would be safe for daily driving on Toronto roads IMO. Chances are a rim would get bent or you might pop a tire. Gotta be safe man lol

[Donutz]

I'm running 17x7 +40's with 215/45's; they are close to flush (maybe a cm inside the rear fender). I'll likely go 225 for my next tires and roll my rear fenders. Fobio has a really nice wide stance, but I don't know how close to flush he is in the rear fender (search for his pics).

Are you thinking like +38 or more (actually less)?

[Dave_The_BMXER]

I posted a few somewhere... I forget where... maybe speed hunters I will look for you.

[Tokic_o]

hmmm, interesting...post some pics!!

I'm thinking of flush and some nice negative camber (hence the car has to be pretty low too ) If its done right I'm pretty sure its safe to drive around town for the most part.

Seen some other cars in TO (imprezas, civics, s2ks) done it. Be nice to see some mazda3s rocking it!

[Donutz]

There are some sick sick 3's on this thread: clickity click

[Gizzmo_jr]

There are some sick sick 3's on this thread: clickity click

Thread win right here

[Dave_The_BMXER]

Ya that's the thread where the best are.

That car above though... too much.

[blackaccord]

just buy my advans and refinish them

[Nextmod]

Thread win right here

thats Hellarub lol

[Donutz]

Some of my fav's from that thread:

[Riftler]

*noob jumps in* Whats hellaflush?

[-RJ3-]

*noob jumps in* Whats hellaflush?

Just look at the wheels, and their offset. Flush to the fender.

[Dave_The_BMXER]

[jonjon72]

Damn that looks sweet.....but ya, our roads in the GTA would kill the car. sigh.

[Tokic_o]

wow those are hot!!

Jason, do you know the specs on the wheels on those 2 black hatches?!?! lol

[Donutz]

The guy with the gold wheels: 18"x9" et +30 Rota G-force on 245's

The guy with chrome wheels: 19 inch with 8.5 at front dan 9.5 at back with et36

[Kevin@nextmod]

I'm saving up for a set of rpf1s 17x8.5 45 offset with 20mm spacers and then polish them and slam my car eve lower at around 2.5 inches.

[Kevin@nextmod]

I know this is a mazda 3 only thread but i found this just now and holy cow its retarded. Golf with lambo rims

[RedRaptor]

Nice thread. I'm also really starting to feel the aggressive look as well.

For those worried about GTA roads. I drive a lot downtown Toronto and all you have to do is pay attention to where you're going. The only time I hit potholes is when I'm distracted or I'm not paying attention at all.

Get a nice set of HIDs and HID fogs for maximum visibility at night.

An aggressive set up or 19" rims doesn't automatically mean you'll be stranded on the side of the road. I've seen 16" steelies with a 60 series tire profile bent.

[azn_outlaw]

Funny how now another trend the Mazda3 community could possibly jump on

But uhhhh folks.....to run these type of setups, you are aware a certain amount of negative camber must be used to actually used to properly run aggressive

Yet from what I remember a majority of you guys HATE NEGATIVE camber and want positive camber

True point RedRaptor that any tire and any series height can bend any rim either steel or OEM

There are some things to remember when going aggressive/hella flush this:

Cost of the rim (no matter how careful you guys are, bend that SOB, and you are out a high 3 figure number for just one rim)

High stress on the wheel bearings, VW/Honda are cheap to replace wheel bearings so they can accomplish without breaking a sweat....Arent Mazda3 wheel bearings hell to purchase and replace...plus are very weak?

High stress on the wheel studs, aggressive negative camber and really bad GTA roads, could possibly snap a wheel stud, easy to replace on a Honda/VW, yet a Mazda3....it can be done but how many times will you be doing this?

Tires is another main factor, killer negative and running highly close to the fenders, could cause a minor rub here and there, plus tire life at such a extreme negative degree again will make tires not last long. In the US they can get away with this cause tire prices can be very dirt cheap. So they can either burn a set and replace cheaply or if one tire pops, then easy to replace.

Remember clearance is an odd one on the Mazda3 from what i find they do not have deep fender wheels like a VW/Honda...

plus there is a McPherson strut in the way, so say good by to your lowering springs, cause to make room...gotta go with a full-coilover.....

There is some light reading....

so who is first in the GTA to do this on a Mazda3? Other then Pearly, its not fair he gotta a honda

[Tokic_o]

^^^ its really tempting to give this a try. I found a nice set of rims, actually going to test fit them. I already have a camber kit and I'm going to roll my fenders already.

but the wheels I found (well nextmod found) is 18x9 +32 offset. 225/40/18 tires. See how it fits first. Just an idea still hope it works out

[Kevin@nextmod]

wow.. 225 tires on x9 rims. big time stretch

[-RJ3-]

High stress on the wheel bearings, VW/Honda are cheap to replace wheel bearings so they can accomplish without breaking a sweat....Arent Mazda3 wheel bearings hell to purchase and replace...plus are very weak?

High stress on the wheel studs, aggressive negative camber and really bad GTA roads, could possibly snap a wheel stud, easy to replace on a Honda/VW, yet a Mazda3....it can be done but how many times will you be doing this?

I can vouche for this... If I can easily crack an FD Rim at regular camber (Thanks to the potholes of GTA) what more will I do with negative... Plus the Wheel bearings (knock on wood) I currently run is the original ones I have had on my car. So far no problems yet.

If I where anyone who wants to jump on this VDub Idea, They should consider running this for show purposes only.... Running this on everyday streets of GTA will kill your pocket not to mention add more frustration in the long run.

[Tokic_o]

wow.. 225 tires on x9 rims. big time stretch

yeah, the original owner of the wheels had 215 tires on them! too much IMO