What Did You Do To Your Car Today?

[MS3Edge]

Well how about what will I be doing to my car tonight. ..... Redoing the from lip after I busted it today 1hour after putting it back on after paint. Just left Karmaspeed's place and just as I pulled out caught it on the curb and tore the side off... Dam this lip kit

[jakesms3]

Went to nextmod to pick up my cpe downpipe and cobb shiftknob

[Reddie1337]

Auto diming mirror install.

Pretty smooth. 2014's have a direct plug, had to cut that off to make it work.

[rzapata]

Pulled over to the side and got ticketed for repping TM3.

Well, the plate cover's "covering" the stickers on the plate that's why. Alberta plates suck!

[Jackal]

Pulled over to the side and got ticketed for repping TM3.

Well, the plate cover's is "covering" the stickers on the plate that's why. Alberta plates suck!

Wow. Took one for the team.

[Karmaspeed]

Well how about what will I be doing to my car tonight. ..... Redoing the from lip after I busted it today 1hour after putting it back on after paint. Just left Karmaspeed's place and just as I pulled out caught it on the curb and tore the side off... Dam this lip kit

yeah when I heard that crack I was like "oh for f#$% sakes". Like the others said no more fiberglass, check out the charger lip from garage16

[MS3Edge]

I Will..pulled front bumper when I got home and put it on tight for today but will look this week

[jaimie08mazda3]

Spent 13 hours replacing the transmission and the CV shaft. God what a pain in the ass. I'm thankful I had a few people helping but never doing that again! Holy hell.

[rzapata]

Wow. Took one for the team.

Haha yeah, would have been nice if I got away with it.

Cop was cool though, he asked about TM3 and complimented the car. Ticket wasn't much so what the hell... I'll pay up.

[Genpu_Mz3]

Put this stupid thing on

[ski-guru]

Put this stupid thing on

How much of a pain in the arse is it to get that on?

[Genpu_Mz3]

How much of a pain in the arse is it to get that on?

Now i know how prolly 2hrs. But it took me 1.5hrs to get the stock one out

[Stupidducky]

Put in K & N filters

[r4BBiT]

Put this stupid thing on

Any power gains or just louder?

[Genpu_Mz3]

Any power gains or just louder?

Tbh i havnt really drove the car too hard. Things to damn loud without a cat. Im sure there will be power gains. How much? I dunno. Not much.

[silverstarmazda]

looks like a lot of people are buying weapons of mass exhaustion lately

[Reddie1337]

Wrapped some new rubber.

Hercules Raptis WR1 225/40ZR18

Road hazard warranty. Had to use it last time I bought these and popped 2 tires.

[dentinger]

Any power gains or just louder?

assuming it's N/A, you'll lose some low end, gain some high end, and gain a hell of a lot of noise.

i found my 2.0 to fall on it's face until about 3k rpm.

[Genpu_Mz3]

assuming it's N/A, you'll lose some low end, gain some high end, and gain a hell of a lot of noise.

i found my 2.0 to fall on it's face until about 3k rpm.

Im finding the opposite. 5k - 7k it falls off

[dentinger]

you might be right. i had my mazda years ago, and it might have just been noise that made me think it was faster.

[MS3Edge]

My halo prosport gauges arrived so I mounted them in the pillar pods. Now have to take Friday off work to have them all hooked up for Saturday at dyno day

[Hyperion]

My halo prosport gauges arrived so I mounted them in the pillar pods. Now have to take Friday off work to have them all hooked up for Saturday at dyno day

Where'd you get your pillar pods?

[MS3Edge]

Glow shift on eBay. Cost me $35 plus $9.99 shipping. Comes in the 3 factory colors beige. Black. Or grey. I will post a picture in a bit. Haven't quite got tapatalk to work fully for me yet with pictures

[Hyperion]

Glow shift on eBay. Cost me $35 plus $9.99 shipping. Comes in the 3 factory colors beige. Black. Or grey. I will post a picture in a bit. Haven't quite got tapatalk to work fully for me yet with pictures

No worries, that's the one I ordered too.

[MS3Edge]

Yes. It's a good fit